Browsing School of Engineering by Title
Now showing items 1-20 of 3072
-
A 12 month prospective cohort study of injury in international rowers.
(2010)Objective: In this study, the injury incidence and association with type and volume of training in international rowers were described. Design: A prospective cohort design was used over a 12- month period. Patients: ... -
3-D Beam-Steering MIMO Antenna for On-Body IoT Applications
(2024)In this article, a compact 3D beam-steering MIMO antenna operating at 5.75 GHz is proposed for on-body Internet of Things (IoT) applications. The planar antenna comprises a central patch and two concentric annular rings. ... -
3-dimensional solder paste inspection using Structured Light techniques
(Trinity College (Dublin, Ireland). Department of Electronic & Electrical Engineering, 2002)Re-modelling of three-dimensional solder paste constructed from optical profilometry has gathered ever-increasing attention in different inspection and process control sectors of the electronics Printed Circuit Board ... -
3D Bioprinted Cartilaginous Templates as Developmentally Inspired Implants for Large Bone Defect Regeneration
(Trinity College Dublin. School of Engineering. Discipline of Mechanical & Manuf. Eng, 2022)Whilst bone possesses an inherent capacity for regeneration, defects above a critical size cannot heal on their own. Damaged or diseased bone can be treated using autografts or a range of different bone grafting biomaterials, ... -
3D bioprinting of cartilage-mimetic implants for biological joint resurfacing
(Trinity College Dublin. School of Engineering. Discipline of Mechanical & Manuf. Eng, 2020)A major challenge in the field of tissue engineering and regenerative medicine is the development of effective therapies for treating large cartilage or osteochondral defects and ultimately regenerating whole osteoarthritic ... -
3D Bioprinting of Developmentally Inspired Templates for Bone and Joint Regeneration
(Trinity College Dublin. School of Engineering. Discipline of Mechanical & Manuf. Eng, 2018)There is an urgent need to develop alternatives to synthetic joint prosthesis to promote the regeneration of diseased osteoarthritic joints. Cell based therapies have shown promise for repairing cartilage and bone; however, ... -
3D bioprinting of prevascularised implants for the repair of critically-sized bone defects
(2021)For 3D bioprinted tissues to be scaled-up to clinically relevant sizes, effective prevascularisation strategies are required to provide the necessary nutrients for normal metabolism and to remove associated waste by-products. ... -
3D bioprinting spatiotemporally defined patterns of growth factors to tightly control tissue regeneration
(2020)Therapeutic growth factor delivery typically requires supraphysiological dosages, which can cause undesirable off-target effects. The aim of this study was to 3D bioprint implants containing spatiotemporally defined patterns ... -
3D Bioprinting Strategies To Engineer Structurally Organised Meniscal Tissue Grafts
(Trinity College Dublin. School of Engineering. Discipline of Mechanical & Manuf. Eng, 2023)Lesions to the meniscus are common sports-related injuries that can lead to articular cartilage degeneration and osteoarthritis if left untreated. While surgical repair procedures and meniscal substitutes offer better ... -
3D deformation and strain fields in drying kaolinite obtained from tracking internal bubbles using X-ray CT and ANN
(2024)Drying fine-grained sediments experience shrinkage and desiccation cracking that may dramatically alter their mechanical and hydraulic properties. This study adopts X-ray computed tomography (CT) to monitor the three-dimensional ... -
3D Modelling Tool to Optimise Advanced Plasmonic Luminescent Solar Devices for Building Integrated Photovoltaic Applications
(Trinity College Dublin. School of Engineering. Disc of Civil Structural & Environmental Eng, 2019)This research concentrates on modelling and optimisation of a static building integrated PV (BIPV) component in which both direct and diffuse solar radiation are harvested through luminescent solar (LS) devices. Plasmonic ... -
A 3D printed acoustic metamaterial liner to reduce low-frequency aeroengine noise
(Trinity College Dublin. School of Engineering. Discipline of Mechanical & Manuf. Eng, 2023)As the level of air travel continues to increase, so too does the demand for better noise-reduction technologies for aircraft. The environmental noise produced by aircraft has been shown to have a significant adverse effect ... -
3D printed microchannel networks to direct vascularisation during endochondral bone repair
(2018)Bone tissue engineering strategies that recapitulate the developmental process of endochondral ossification offer a promising route to bone repair. Clinical translation of such endochondral tissue engineering strategies ... -
3D printing of fibre-reinforced cartilaginous templates for the regeneration of osteochondral defects
(2020)Successful osteochondral defect repair requires regenerating the subchondral bone whilst simultaneously promoting the development of an overlying layer of articular cartilage that is resistant to vascularization and ... -
3D-Printed Air-Cathodes for Microbial Fuel Cells: Advancing Pollutant Removal and Energy Recovery from Wastewater
(Trinity College Dublin. School of Engineering. Disc of Civil Structural & Environmental Eng, 2025)Worldwide, 300 billion m3 of domestic wastewater was produced every year, which contained around 600 billlion kWh of energy. Current wastewater treatment methods, which rely heavily on aeration, are highly energy-intensive, ... -
A Bayesian Approach for Inferring the Topology of a System of Interdependent Infrastructure Networks: A Case Study of the U.K. Interdependent Power-Gas System
(2023)Understanding the behavior of complex systems is essential to plan for future disasters that impact complex systems including infrastructure, social, and environmental systems. The complexity of the behavior of these systems ...
